The cart is empty

Cannot find your purchased courses? Click here to Login!

Going to truck driving school? Know what to expect.

Truck Driving School | CDL Training


Update May 2022


The five components of a CDL Driver Training course are:

1) turning;

2) shifting;

3) pre-trip inspection;

4) backing

5) hooking and unhooking the trailer.


The first three:

1) turning;

2) shifting;

3) pre-trip inspection


These are the major components of the course.The last two:

4) hooking & unhooking

5) backing

These abilities & skills are dependent on the DMV (Department of Motor Vehicles) at which you will be tested.



The first one, turning.

As I always tell my students - most of them are so consumed by trying to shift a non-synchromesh transmission, it takes all of their energy, all of their time that it overshadows the importance of turning.

And what I tell my students is, turning is gonna get you into trouble!

It is going to get you hurt, your gonna pull the trailer up over somebody's car and they're going to be very excited when that happens!

Let me you, you pull the duals of that trailer up over the front end somebody's car on a left-hand turn - screaming, crying, jumping up and down - it is not a good scene.

Turning in my mind on a CDL driver training course is the most important aspect of the course and what you will learn.



Shifting, the second thing that you are going learn on a CDL driver training course.

Shifting is difficult because it is a non-synchromesh transmission.

And in that non-synchromesh transmission, it's up to the driver to synchronize the transmission.

and by doing that you have to match up:

1) the road speed

2) the gear

3) and the engine RPM.

Now the engine rpm is a misnomer because actually what you're doing is synchronizing the speed of the gears in the transmission.

But the only way that we have to determine how fast the gears in the transmissions are going is through the rpm, the tachometer on the dash.

In order to speed the gears up in the transmission you have to double clutch.

You have to reconnect the transmission to the motor and a lot of students have difficulty with the throttle and the clutch.

Those two things: ones on, one's off - wax on wax off! On that note, as well the clutch - if you push the clutch in too far after your starting gear, you begin to engage the clutch brake and slow the gears down in the transmission.

When you slow the gears down in the transmission you get a rough shift.

You also have to double clutch.

It's imperative that you double clutch - one clutch into neutral, let the clutch out, into gear again with the clutch in.

So you got a double-clutch.

This is not a spectator sport; you have to do it, you have to go to a school and have some one show you how to do it, it's going to make it a lot easier for you.

The Pre-Trip Inspection


Now, most driver licensing centers in North America allow you 45 minutes for pre-trip inspection.

It's a complete, thorough pre-inspection.

You are not determining if the vehicle is safe, you're demonstrating a competency - that you know the names of the major components of the vehicle, what could be wrong with them, and whether they're working or not.

To remember and memorize the CDL pre-trip inspection, stick to the sequence.<p>Left to right and top to bottom.

For more information on the pre-trip inspection see: Trucking | CDL Pre-trip Inspection



The last two components can be somewhat minor.

Backing - some places are just 50 feet straight back.

Here in Vernon, BC - thats what is, it's fifty feet straight back.

Make sure you get out before you back up.

For those people who don't have any experience at all backing up, go out get yourself a pickup truck, borrow somebody's utility trailer and just practice backing up.

All of the principles are the same as they are in a big truck.

Actually a tent trailer is a lot harder to back up than a semi-trailer.

You just need a bit more room with a semi-trailer.

Now just a couple of pointers on backing up:

1) if you want to turn the trailer, put your hand on the bottom of the steering wheel - the way you push the steering wheel is the way that the trailer's going to go.

Now don't let it get too far.

We say to students, look in the mirror - when you can see the dollies, then start to follow it.

2) To follow the trailer, you put your hand on the top of the steering wheel.

And the way the trailer's going is the way you turn the steering wheel.

So, a few pointers on backing - depending on the licensing centre - in Victoria, BC for example, it was quite difficult because the students had to parallel park and that was a bit of a challenge for some.

Don't Work the Day for Free:: DOT Weigh Scale Checklist

This checklist will provide you with a list of paperwork that you need to bring into the authorities when you get pulled into the scale house.

• DID YOU KNOW? :: Bus & truck drivers are the only drivers that have their own police force (DOT, CVSE, MTO, etc.);

• SMART :: There's a lot of paperwork you must produce for authorities at the weigh scale;

• SELF-CONFIDENCE :: Bring all paperwork in one hit & impress the diesel bears!

Because in most cases, it's you that gets the fine...NOT the company!

Get Your Driver's Test Checklist Now!




Now the last one is hooking & unhooking and I tell students it's not a huge deal as long as you don't drop the trailer on the ground, rip the dollies off, or pull the lines off, your OK.

But look at the procedure, follow the procedure.Unhooking:


1) landing gear,

2) airlines,

3) pin.


Hooking up:  - public displays of affection:

1) pin,

2) dollies,

3) airlines.

Keep in mind, landing gear & dollies are the same thing.

They're the legs that hold the trailer up when it's not hooked to the truck.Those are the five components of a tractor-trailer course.


You're going to a driver training school and going to take a tractor-trailer course.

The five components are:

1) turning;

2) shifting;

3) pre-trip inspection

4) hooking/unhooking and

5) backing.

These will vary in difficulty depending on the licensing center.

Turning is the most important.

You need to get the truck around an urban area.

Some times what I tell students is driving truck is a little bit like being a soldier in the Vietnam War, or any war for that matter.

It's hours and hours of sheer boredom punctuated by a few moments of sheer terror.

Sometimes it's a bit of terror to get these things around a city because they're in spots they're not designed to be in.

The second one is shifting.

Shifting a non-synchromesh transmission is not a spectator sport.

You gotta get in the seat - you gotta do it.

You're going to learn by doing.

It's easier under the tutelage of somebody who knows how to do it, who can teach you how to do it.

So keep that in mind.

The other one is pre trip-inspection.

Pre-trip inspection is more or less memorization.

Once you've done it a few times it gets a lot easier.

The last two are the minor components I call them.

Hook-unhook and backing up.

If you've had backing up experience before, it's going to be fairly straightforward.

It'll also depends on the licensing center and what are the requirements for backing up.Hook-unhook:

PDA‚”public displays of affection” for hooking up:

1) Pin;

2) Dollies

3) Airlines & Electrical.

Unhooking – LAP

1) Landing gear;

2) Airlines

3) Pin

Do it in the same order every time! That way you won't: drop it on the ground; you won't rip the legs off; and you won't rip the lines off.

All the best at truck driving school; good luck on your CDL Driver's test!

Log in to comment

© Smart Drive Test Inc. 2024.

Contact Us: [email protected]